How to read a vernier caliper

Step by step with pictures: the parts, how to measure, then how to read the main scale and find the vernier line that lines up. Each step shows the scales with the part you are reading marked.

How to read an inch vernier caliper, step by step

1 Know the parts

Inside jawsInside jawsLock screwMain scale on the beamDepth rodOutside jawsOutside jawsVernier scaleThumb roller
The parts of a vernier caliper.

The beam carries the main scale. The sliding jaw moves along it: roll it with the thumb roller and hold it with the lock screw. The big outside jaws measure across a part, the small inside jaws measure holes and slots, and the depth rod comes out of the end to measure how deep something is. The vernier scale on the slide reads the thousandths.

2 Measure the outside of a part

The part goes between the outside jaws
Close the outside jaws on the part, near the base of the jaws.
  1. Wipe the jaws, close them and check the caliper reads zero.
  2. Open the jaws wider than the part, then close them gently and squarely on it. Use the part of the jaws near the beam, not the tips.
  3. Light, even pressure. Squeezing hard bends the jaws and reads small.
  4. Read it on the part, or lock it and lift it off.

3 Know the scales

Whole caliper0123456Magnified view of the scales234567893105101520250.001 inEach small number = 0.100"Big number = whole inchEach small space = 0.025"Each vernier line = 0.001"
Big numbers are inches, small numbers are tenths (0.100"), each small space is 0.025" and each vernier line is 0.001".

The main scale counts inches (big numbers) and tenths of an inch (small numbers 1 to 9, each 0.100"). Each tenth is split into 4 small spaces of 0.025". The vernier scale on the slide has 25 lines, each worth 0.001".

4 Read the main scale up to the vernier zero

Whole caliper0123456Magnified view of the scales234567893105101520250.001 inMain scale: 2.325"
The vernier zero has passed 2 inches, 3 tenths and one small space: 2.325".

Look at where the 0 of the vernier sits. Read everything it has passed: inches, then tenths, then small spaces. Here: 2.000 + 0.300 + 0.025 = 2.325".

5 Find the vernier line that lines up

Whole caliper0123456Magnified view of the scales234567893105101520250.001 inLine 22 lines up = 0.022"
Vernier line 22 lines up exactly with a main-scale line: add 0.022".

Run your eye along the vernier. Only one line lines up exactly with a line on the main scale. Its number is the thousandths. Tip: the lines on either side of it are off by the same small amount in opposite directions.

6 Add them up

Whole caliper0123456Magnified view of the scales234567893105101520250.001 inMain scale: 2.325"Line 22 lines up = 0.022"2.325 + 0.022 = 2.347"
2.325 + 0.022 = 2.347".

Main scale plus vernier: 2.347".

How to read a metric vernier caliper

1 Read the whole millimetres

Whole caliper012345678910111213141516Magnified view of the scales2340123456789100.1 mmMain scale: 23 mm
The vernier zero is just past the 23 mm line: 23 mm.

The main scale is in millimetres, numbered every centimetre (the 2 is 20 mm, the 3 is 30 mm). Read the last millimetre line the vernier zero has passed.

2 Find the vernier line that lines up

Whole caliper012345678910111213141516Magnified view of the scales2340123456789100.1 mmLines up at 4 = 0.40 mm
Vernier line 4 lines up with a main-scale line: 0.40 mm.

On a 0.1 mm vernier each line is 0.1 mm. Find the one line that lines up exactly with a main-scale line.

3 Add them up

Whole caliper012345678910111213141516Magnified view of the scales2340123456789100.1 mmMain scale: 23 mmLines up at 4 = 0.40 mm23 + 0.40 = 23.4 mm
23 + 0.40 = 23.4 mm.

Whole millimetres plus the vernier: 23.4 mm.

4 Finer verniers: 0.05 mm

Whole caliper012345678910111213141516Magnified view of the scales2345670123456789100.05 mmMain scale: 23 mmLines up at 4.5 = 0.45 mm23 + 0.45 = 23.45 mm
On a 0.05 mm vernier the numbers count tenths. It lines up halfway between 4 and 5, at 4.5: 23 + 0.45 = 23.45 mm.

A 0.05 mm vernier has 20 lines, with numbers that count tenths of a millimetre. A line halfway between two numbers adds 0.05 mm. A 0.02 mm vernier is read the same way with 0.02 mm per line.

Try it yourself

Slide the caliper and watch which vernier line lines up. The top shows the whole caliper; below it is a magnified view of the scales, like looking through a loupe.

How a vernier works

A vernier scale is a second scale whose lines are spaced a tiny bit closer than the main scale's. On an inch caliper, 25 vernier lines fit in the space of 24 main divisions, so each vernier line falls 0.001" shorter than the main line next to it. Only one vernier line can line up exactly with a main-scale line, and which one it is tells you the thousandths.

Other ways to measure

The same scales read inside, depth and step measurements. The caliper guide shows each one with a picture. For a step, put the end of the slide against the shoulder and the end of the beam on the lower surface.

Practise reading a vernier caliper

Practice this tool Take a timed test Print a free worksheet

Questions

How do you read a vernier caliper in inches?

Read the main scale up to the vernier zero (inches, tenths and 0.025" divisions), then add the number of the vernier line that lines up exactly, in thousandths.

What is the least count of a vernier caliper?

The smallest step it can read: 0.001" on most inch verniers, and 0.1, 0.05 or 0.02 mm on metric ones.

Why do two vernier lines look lined up?

On a drawing or a worn tool, two neighbouring lines can look close. The true one is where the lines on both sides drift away evenly. If the 0 and last line both line up, the vernier adds nothing.

What is the difference between a vernier and a dial caliper?

A dial caliper replaces the vernier with a gear-driven dial that you read directly. A vernier has no moving parts to wear but takes more care to read.

Sources

Measure Drill checks every number against these references or works it out from the exact definitions of the units.