How to read a micrometer

Step by step with pictures: the parts, how to measure, then how to read the sleeve and thimble. Each step shows the micrometer with the part you are reading marked.

How to read an inch micrometer, step by step

1 Know the parts

FrameAnvilSpindleLockSleeve (barrel) with the main scaleThimbleRatchet
The parts of an outside micrometer.

The C-shaped frame holds a fixed anvil on one side. The spindle moves in and out when you turn the thimble. The sleeve (also called the barrel) has the main scale and a long reference line. The ratchet on the end slips at a set force so every measurement is taken with the same pressure, and the lock holds the spindle still.

2 Measure the part

Part between anvil and spindleTurn the ratchet until it clicks
The part sits square between the anvil and the spindle. The ratchet does the final tightening.
  1. Check zero first: close it gently with the ratchet and make sure it reads exactly 0.
  2. Open it a little wider than the part and put the part between the anvil and the spindle, square, not tilted.
  3. Turn the thimble until the spindle almost touches, then finish with the ratchet until it clicks two or three times. Do not force the thimble.
  4. Read it on the part, or turn the lock and slide it off carefully.

3 Read the last number on the sleeve

0-1 IN20001233 = 0.300"
The last number you can see on the sleeve is 3, so 0.300".

Each number on the sleeve is 0.100": 1 is 0.100, 2 is 0.200, 3 is 0.300. Find the last number the thimble edge has uncovered.

4 Count the small lines after it

0-1 IN20001232 small lines x 0.025 = 0.050"
Two small lines show after the 3: 2 x 0.025 = 0.050".

Between two numbers there are three small lines, and each one is 0.025" (one full turn of the thimble). Count only the lines you can actually see past the number. A line hidden under the thimble edge does not count yet.

5 Read the thimble

0-1 IN2000123Thimble 22 = 0.022"
Thimble line 22 sits on the reference line: 0.022".

The thimble has 25 lines around it, each 0.001". Read the thimble line that sits on the long reference line of the sleeve. If it is between two lines, take the lower one.

6 Add them up

0-1 IN20001233 = 0.300"2 small lines x 0.025 = 0.050"Thimble 22 = 0.022"0.300 + 0.050 + 0.022 = 0.372"
0.300 + 0.050 + 0.022 = 0.372".

Add the three parts: number, small lines and thimble. 0.300 + 0.050 + 0.022 = 0.372". That is the whole method for any inch micrometer.

7 Vernier micrometers: one more digit

0-1 IN101520001201234567890Vernier 6 lines up = 0.0006"
Vernier line 6 lines up exactly with a thimble line: add 0.0006".

Some micrometers read to ten-thousandths. They have 10 extra lines on the sleeve, above the reference line. First read to the thousandth as before (here 0.287"). Then find the one vernier line that lines up exactly with a thimble line. Its number is the fourth decimal place.

8 Add all four parts

0-1 IN1015200012012345678902 = 0.200"3 small lines x 0.025 = 0.075"Thimble 12 = 0.012"Vernier 6 lines up = 0.0006"0.2000 + 0.0750 + 0.0120 + 0.0006 = 0.2876"
0.2000 + 0.0750 + 0.0120 + 0.0006 = 0.2876".

Number, small lines, thimble, vernier: 0.2876".

9 Bigger micrometers: add the frame size

1-2 IN20001233 = 0.300"2 small lines x 0.025 = 0.050"Thimble 22 = 0.022"1.000 + 0.300 + 0.050 + 0.022 = 1.372"
A 1-2" micrometer: add 1.000" to what the scales show. 1.000 + 0.300 + 0.050 + 0.022 = 1.372".

A 1-2" micrometer cannot close below 1 inch, so add 1.000" to the reading. A 2-3" adds 2.000", and so on. The size is marked on the frame. Forgetting this is one of the most common test mistakes.

How to read a metric micrometer

1 Whole millimetres above the line

0-25 MM3035057 mm (last top line)
The last line showing above the reference line is 7: 7 mm.

On a metric micrometer the lines above the reference line are whole millimetres, numbered every 5. Find the last one the thimble has uncovered.

2 Half millimetres below the line

0-25 MM303505Half line showing: + 0.50 mm
A half line shows below the reference line after the 7: add 0.50 mm.

The lines below the reference line are the half millimetres. If one shows after the last whole millimetre, add 0.50 mm. If not, add nothing.

3 Read the thimble

0-25 MM303505Thimble 32 = 0.32 mm
Thimble line 32 sits on the reference line: 0.32 mm.

The thimble has 50 lines, each 0.01 mm. One turn is half a millimetre.

4 Add them up

0-25 MM3035057 mm (last top line)Half line showing: + 0.50 mmThimble 32 = 0.32 mm7.00 + 0.50 + 0.32 = 7.82 mm
7.00 + 0.50 + 0.32 = 7.82 mm.

Whole millimetres, plus the half if it shows, plus the thimble: 7.82 mm. With no half line it would have been 7.32 mm.

5 25-50 mm micrometers

25-50 MM3540452527 mm (last top line)No half line showing: + 0.00Thimble 40 = 0.40 mm27.00 + 0.00 + 0.40 = 27.40 mm
A 25-50 mm micrometer is numbered from 25. Last line 27, no half line, thimble 40: 27.40 mm.

Bigger metric micrometers are usually numbered from their starting size, so read the number straight off the sleeve.

Try it yourself

Turn the micrometer with the slider and watch how the sleeve and thimble add up. Switch on the vernier for ten-thousandths, or switch to metric.

Good habits

Practise reading a micrometer

Practice is free and unlimited, with a fresh drawing every time.

Practice this tool Take a timed test Print a free worksheet

Questions

How many thousandths is one turn of a micrometer?

One turn of an inch micrometer is 0.025", which is 25 thousandths. That is why the thimble has 25 lines.

What is each line on the sleeve of a micrometer?

On an inch micrometer, numbered lines are 0.100" and the small lines between them are 0.025". On a metric micrometer, lines above the reference line are whole millimetres and lines below are half millimetres.

How do you read a micrometer to 0.0001?

Read it to the thousandth, then find the vernier line on the sleeve that lines up with a thimble line. Its number is the fourth decimal place.

How do I read a 1-2 inch micrometer?

Read it the same way, then add 1.000 inch, because the smallest it can measure is 1 inch.

How accurate is a micrometer?

A standard inch micrometer reads to 0.001", a vernier micrometer to 0.0001", and a metric micrometer to 0.01 mm.

Sources

Measure Drill checks every number against these references or works it out from the exact definitions of the units.