How to read a tape measure
Follow the pictures step by step: what every little mark means, then how to read a measurement. Then try it yourself with the guided lesson and unlimited practice.
How to read a tape measure, step by step
1 Find the inch lines
The longest lines, the ones with numbers, are the whole inches. Between two numbers is one inch, and every inch on the tape looks exactly the same. Once you can read one inch, you can read all of them. The marks in between split that inch into smaller pieces, and the next steps show each kind.
2 The half inch: the longest mark in between
Halfway between the inch numbers is the longest of the in-between marks. It is the half inch, 1/2". If the end of what you are measuring lands on it, the reading is the inch number and a half, like 1 1/2".
3 Quarter inches: the next longest marks
Halfway between the inch line and the half inch is the quarter inch, 1/4". Halfway between the half and the next inch is 3/4". These are the next longest marks. The half inch is also 2/4, so the quarters go 1/4, 2/4 (1/2), 3/4.
4 Eighths: the short marks
Shorter again are the eighths: 1/8", 3/8", 5/8" and 7/8". They sit halfway between the quarter marks. The even eighths already have simpler names: 2/8 is 1/4, 4/8 is 1/2 and 6/8 is 3/4.
5 Sixteenths: the shortest marks
The shortest marks are the sixteenths: 1/16", 3/16", 5/16" and so on up to 15/16". With these, the inch is split into 16 equal pieces. Every mark on the inch is some number of sixteenths, which is why counting sixteenths always works.
6 Read a measurement: start, count, simplify
- Start at the last inch number before the end of what you are measuring. Here that is 1.
- Count the little marks from that line to the end: 6. That is 6/16.
- Simplify: if the top number is even, halve both numbers until it is odd. 6/16 becomes 3/8.
- Put them together: 1 3/8 inches. You can check it: the arrow is right on the 3/8 mark.
7 Read past 12 inches: feet and inches
Past 12 inches the numbers keep going: 13, 14, 15 and on. Most tapes also mark each foot, often with a red box or a small "1F" at 12 and "2F" at 24. To say a reading in feet and inches, take out 12 inches for every foot: 25 5/16" is 24" (2 feet) plus 1 5/16", so it is 2' 1 5/16". Both ways of writing it are the same length.
Reading the metric side
1 Centimetres and millimetres
On the metric side, the numbered lines are centimetres. Each centimetre is split into 10 millimetres by the small marks. The slightly longer mark in the middle is 5 mm, half a centimetre.
2 Read a metric measurement
Start at the last centimetre number (4 cm is 40 mm), count the millimetre marks to the end (7), and add them: 47 mm. The same length can be written 4.7 cm. No fractions to simplify on the metric side.
3 The same reading at normal size
This is the same 47 mm at normal size. The 5 mm marks help you count quickly: 47 is two marks past the 5 mm mark after the 4.
Start here: a 3-step lesson
Try it yourself
Drag the tape and watch the reading change. Every step is written out.
Red numbers and black diamonds
Many tapes highlight every 16 inches (16, 32, 48...) in red. That is the standard spacing for wall studs, 16 inches on center. Some tapes also have small black diamonds every 19.2 inches (just over 19 3/16"), which splits 8 feet into five equal spaces for joists or trusses. You do not need these to read a measurement, but now you know why they are there.
Why the hook is loose
The metal hook on the end slides in and out by about its own thickness, roughly 1/16". When you hook it over an edge it pulls out; when you push it against a wall it pushes in. That movement makes the zero point correct both ways, so do not try to fix it.
Common mistakes
- Counting the inch line itself as the first mark. Start counting from the mark after it.
- Reading from the next inch instead of the last one, which gives a number one inch too big.
- Writing 5 6/16 instead of 5 3/8. It is the same length, but most tests and job sheets want the fraction in lowest terms.
- Mixing feet and inches: 2' 3" is 27", not 23".
Practise reading a tape measure
Start at level 1 and move up when you are getting them right. Type the reading, or switch to multiple choice. Tape measure practice is free and unlimited.
Tape measure fractions chart
Every sixteenth of an inch with its decimal and millimetre value. Decimals are exact; millimetres are rounded to two places.
| Sixteenths | Fraction | Decimal inch | Millimetres |
|---|---|---|---|
| 1/16 | 1/16" | 0.0625 | 1.59 |
| 2/16 | 1/8" | 0.125 | 3.18 |
| 3/16 | 3/16" | 0.1875 | 4.76 |
| 4/16 | 1/4" | 0.25 | 6.35 |
| 5/16 | 5/16" | 0.3125 | 7.94 |
| 6/16 | 3/8" | 0.375 | 9.53 |
| 7/16 | 7/16" | 0.4375 | 11.11 |
| 8/16 | 1/2" | 0.5 | 12.70 |
| 9/16 | 9/16" | 0.5625 | 14.29 |
| 10/16 | 5/8" | 0.625 | 15.88 |
| 11/16 | 11/16" | 0.6875 | 17.46 |
| 12/16 | 3/4" | 0.75 | 19.05 |
| 13/16 | 13/16" | 0.8125 | 20.64 |
| 14/16 | 7/8" | 0.875 | 22.23 |
| 15/16 | 15/16" | 0.9375 | 23.81 |
| 16/16 | 1" | 1 | 25.40 |
Questions
What is the smallest mark on a tape measure?
Usually 1/16 of an inch. Some tapes mark 1/32 of an inch for the first 12 inches.
How many lines are in an inch on a tape measure?
Sixteen spaces, so 15 small marks between the inch lines, with the inch lines themselves making the 16th.
What does 5 3/8 look like on a tape?
Five whole inches, then six sixteenth marks more, which is three eighth marks. It lands on an eighth-inch mark, the second shortest kind.
Why are some numbers red on a tape measure?
Red marks every 16 inches show standard stud spacing, 16 inches on center.
What are the black diamonds on a tape measure?
They mark every 19.2 inches (just over 19 3/16"), which splits 8 feet into five equal spaces for joists or trusses.
How do I convert inches to feet and inches?
Take out 12 inches for every foot. 27 5/16 inches is 2 feet (24 inches) and 3 5/16 inches.
Sources
Measure Drill checks every number against these references or works it out from the exact definitions of the units.